ADM202 High Speed, 5 V, 0.1 µF CMOS RS-232 Driver/Receiver

Product DetailsThe ADM202 is a 2-channel RS-232 line driver/receiver pair designed to operate from a single 5 V power supply. A highly efficient on-chip charge pump design permits RS-232 levels to be developed using charge pump capacitors as small as 0.1

LTC1385 3.3V Low Power EIA/TIA-562 Transceiver

Product DetailsThe LTC1385 is an ultra-low power, 2-driver/2-receiver EIA / TIA-562 transceiver which operates from a single 3.3V supply. The charge pump requires only four spacesaving 0.1µF capacitors.The transceiver operates in one of three modes:

ADM488 5 V, Slew-Rate Limited, Low Power, 250 kbps, Full Duplex EIA RS-485 Transceiver

Product DetailsThe ADM488 andADM489are low power differential line transceiver suitable for communication on multipoint bus transmission lines.They are intended for balanced data transmission and comply with both EIA Standards RS-485 and RS-422. Both prod

ADM3491 3.3 V, Low Power, RS-485/RS-422 Transceiver (Full Duplex, 10 Mbps, Driver/Receiver Enable)

Product DetailsThe ADM3491 is a low power differential line transceiver designed to operate using a single +3.3 V power supply. Low power consumption coupled with a shutdown mode make it ideal for power sensitive applications. It is suitable for communica

ADM3315E 15kV ESD Protected,+2.7V to +3.6V Serial Port Transceiver w/ Green Idle™

Product DetailsOperating from a single supply as low as +2.7 V, the ADM3315E is a three-driver/three-receiver serial port transceiver, and fully meets full EIA-232 standards.It is similar to the ADM3312E but with the Power Supply Current reduced by up to

ADM3310E +2.7 V Serial Port RS-232 Transceiver (3 Drivers / 5 Receivers) with 15kV ESD

Product DetailsThe ADM3310E is a three-driver/five-receiver serial port transceiver, which meets EIA-232 standards while operating from a single power supply as low as +2.7V. It is similar to the ADM3311E but with two of the Receivers remain Active during

LTC2862 ±60V Fault Protected 3V to 5.5V RS485/RS422 Transceivers

Product DetailsThe LTC2862/LTC2863/LTC2864/LTC2865 are low power, 20Mbps or 250kbps RS485/RS422 transceivers operating on 3V to 5.5V supplies that feature ±60V overvoltage fault protection on the data transmission lines during all modes of operatio

ADM2682E 16Mbps, 5 kV rms Signal & Power Isolated RS-485 Transceiver with ±15 kV ESD Protection

Product DetailsThe ADM2682E/ADM2687E are fully integrated 5 kV rms signal and power isolated data transceivers with ±15 kV ESD protection and are suitable for high speed communication on multipoint transmission lines. The ADM2682E / ADM2687E includ

LTC1343 Software-Selectable Multiprotocol Transceiver

Product DetailsThe LTC1343 is a 4-driver/4-receiver multiprotocol transceiver that operates from a single 5V supply. Two LTC1343s form the core of a complete software-selectable DTE or DCE interface port that supports the RS232, RS449, EIA-530,EIA-530-A,

LTC1344 Software-Selectable Cable Terminator

Product DetailsThe LTC1344 features six software-selectable multiprotocol cable terminators. Each terminator can be configured as an RS422 (V.11) 100Ω minimum differential load, V.35 T-network load or an open circuit for use with RS232 (V.28) or RS423 (V.

ADN4691E 3.3 V, 200 Mbps, Half-Duplex, High Speed M-LVDS Transceiver with Type 1 Receiver

Product DetailsThe ADN4691E /ADN4693E/ADN4696E/ADN4697Eare multipoint, low voltage differential signaling (M-LVDS) transceivers (driver and receiver pairs) that can operate at up to 200 Mbps (100 MHz). The receivers detect the bus state with a differentia

ADN4650 5 kV rms, 600 Mbps Dual Tx or Rx Channel LVDS Isolator

Product DetailsThe ADN4650/ADN4651/ADN4652are signal isolated, low voltage differential signaling (LVDS) buffers that operate at up to 600 Mbps with very low jitter.The devices integrate Analog Devices, Inc.,iCoupler®technology, enhanced for high spee

ADM2682E 16Mbps, 5 kV rms Signal & Power Isolated RS-485 Transceiver with ±15 kV ESD Protection

Product DetailsThe ADM2682E/ADM2687E are fully integrated 5 kV rms signal and power isolated data transceivers with ±15 kV ESD protection and are suitable for high speed communication on multipoint transmission lines. The ADM2682E / ADM2687E includ

ADM3054 5 kV rms Signal Isolated High Speed CAN Transceiver with Bus Protection

Product DetailsThe ADM3054 is a 5 kV rms signal isolated controller area network (CAN) physical layer transceiver. The ADM3054 complies with the ISO 11898 standard.The device employs Analog Devices, Inc.,iCoupler®technology to combine a 3-channel isol

ADUM3224 3kV rms Isolated Precision Half-Bridge Driver, 4A Output for Automotive

Product DetailsTheADuM3224/ADuM4224are 4 A isolated, half-bridge gate drivers that employ the Analog Devices, Inc.,iCoupler®technology to provide independent and isolated high-side and low-side outputs. The ADuM3224 provides 3000 V rms isolation in th

ADUM1240 Micropower, Dual-Channel Digital Isolators, Default High (2/0 Channel Directionality)

Product DetailsThe ADuM1240 /ADuM1241/ADuM1245/ADuM1246are micropower, dual-channel digital isolators based on the Analog Devices, Inc.,iCoupler®technology. (Quad-channel products available). Combining high speed, complementary metal oxide semiconduct

ADUM142D Robust, Quad Channel Isolator W/ Input Disable & 2 Reverse Channels

Product DetailsThe ADuM142Dis a quad-channel digital isolator based on Analog Devices, Inc.,iCoupler®technology. Combining high speed, complementary metal-oxide semiconductor (CMOS) and monolithic air core transformer technology, these isolation compo

ADUM141D Robust, Quad Channel Isolator W/ Input Disable & 1 Reverse Channel

Product DetailsThe ADuM141Dis a quad-channel digital isolator based on Analog Devices, Inc.,iCoupler®technology. Combining high speed, complementary metal-oxide semiconductor (CMOS) and monolithic air core transformer technology, these isolation compo

LTM2895 100MHz Isolated

Product DetailsThe LTM2895 is a high speed isolated μModule®(micromodule) SPI interface with DAC control signals designed to isolate LTC’s family of general purpose DACs and to isolate general purpose SPI interfaces. The LTM2895 works with DA

ADuM4120 Isolated, Precision Gate Driver with 2 A Output

Product DetailsThe ADuM4120/ADuM4120-1are 2 A isolated, single-channel drivers that employ Analog Devices, Inc.,iCoupler®technology to provide precision isolation. The ADuM4120/ADuM4120-1 provide 5 kV rms isolation in the 6-lead wide body SOIC package

Сторінка 1 / 26